APOLLO Tour

This page will make you acquainted with the arrangement and progress of the APOLLO construction. For pictures taken during the initial laser installation visit, follow this link.

Start the tour by looking at a line figure showing the general location of the components to get a feel for the names and locations of various bits and pieces.

APOLLO and
telescope6/21/06

We start with a picture from behind the telescope. On the back of the telescope, to the left of the ladder, is the laser enclosure—sometimes referred to as "Utah" owing to its shape. In this box sits the laser, the optics/receiver, and the timing electronics.

At lower-left is a box that looks like a metal phone booth. This enclosure, called the cabinet, contains all the electronics that need to be relatively close to the laser and timing system, such as the laser capacitor banks, the control computer, optics controllers, etc.



inside utah05/31/05

This is a peek inside the laser enclosure ("utah"). The doors swing out like refrigerator doors to allow access to the inside. The laser occupies a 2×4 foot section of the 3×4 foot optical bench. A small 100-W heater at lower right is more than enough to keep this well-insulated box warm even on the coldest of nights. The CAMAC crate containing the timing electronics occupies the upper left space. The long black box to the right of the laser is the receiver tube, at the bottom of which is the APD detector and associated electronics. The optics are covered by baffles (silver in picture, now black-anodized). See the SolidWorks design of the optical train to see how the optical path threads through the system. The two black boxes to the left of the laser are air-to-water heat exchangers for removing heat from the thermally-controlled box.



The Cabinet06/25/05

This shows the inside of the cabinet housing the electronics that must be reasonably close to the laser and timing system, but don't need to actually sit on the telescope—and don't require fine temperature controll. At top left is the optics controller for changing beam divergence and relative pointing of the receiver and transmit beams. To the right of this is the laser power meter (absent here). Below this is the STV CCD camera controller. Behind the STV is the flowmeter readout box (hidden). The laser's capacitor banks, responsible for firing the laser flashlamps, sit in the upper right of the cabinet (large units). Below this is the handpad for laser control. On the sliding tray is the user interface for houston, the main APOLLO hardware interface computer, which itself sits at lower right. On top of houston is the analog-input breakout box, through which houston accesses temperature readings, laser power readings, flowmeter readings, and also controls various power outlets for turning equipment on and off. The four stacked boxes are various DC power supplies. The blue box to the left of these is the RTD temperature converter box.

The cabinet is surrounded by 1-inch-thick polyisocyanurate insulation with taped edges and D-seal interfaces. The air volume of the cabinet is contiguous with the intermediate-level (IL) enclosure (see picture below). The thin insulation is not enough to prevent thermal leakage, so the cabinet is surrounded by a sheet-metal plenum for routing ambient cold air around the cabinet outside, thus pulling residual heat out and through slots in the floor. A few of the slots can be seen in the floor along the front edge.



The octopus
vent12/19/03

Below the cabinet (and observing floor) is the "intermediate level" (IL) of the observatory, into which we have built a platform about ten feet off the floor, and four feet below the ceiling (seen here as corrugated decking). Here we see the "octopus" arrangement of ducts that pulls air around the cabinet insulation and dumps it into the intermediate level. A rectangular patch of what will ultimately become the IL enclosure ceiling can be seen, with 1 big hole for pulling air out of the top of the cabinet enclosure (otherwise hot air would pile up here), ten small holes for air return, and three large holes for passing electrical and plumbing lines between the cabinet and IL enclosure.



IL enclosure
under construction02/17/04

The outside of the IL enclosure during construction. A ladder (yellow) and door (blue) can be seen at bottom, giving a sense for the loft-like nature of the IL platform. The angled wall is necessary to allow the "octopus" ducts to pass under the I-beam. The horizontal bar on the near side of the enclosure is Unistrut, which surrounds the IL enclosure and gives it strength.



IL enclosure
complete05/10/04

The finished IL enclosure interior. The ceiling panel interface to the cabinet can be seen at top right. The removable ceiling panels all latch into place and are held down on the edges with bungee cord (red). The louvre at right (actually a double-louvre box) admits air into an exhaust fan, and a similar set of louvres on the other side of the enclosure admits ambient air in. When the system is running, we will be dumping several kilowatts into the intermediate level. From here, air is rapidly moved well away from the telescope by the observatory's air handling system.



IL enclosure,
populated05/10/04

Looking into the double-doors of the IL enclosure, with the primary occupants rolled into place. Through door number one are two chillers; the left (smaller) chiller takes heat out of the laser enclosure on the telescope. The larger chiller removes heat from the laser flashlamps/rods through an interface controlled by the laser electronics rack (lowest unit in the rack). Through door number two is the laser electronics rack, holding everything but the two capacitor units that occupy the top portion of the cabinet enclosure. From top to bottom are the control unit, the RF generator for acousto-optic modulation, two power supply units, and the "cooling group," which controls the thermal state of the laser rods.




APOLLO Main Page